The solid material was dried at 105 °C for 4 h Specific surface

The solid material was dried at 105 °C for 4 h. Specific surface area and pore volume determinations were based on Nitrogen adsorption isotherms at −196 °C (Autosorb – Quantachrome NOVA). The specific surface area was calculated by the Brunauer–Emmett–Teller (BET) method, pore size and total volume were calculated by the Barret–Joyner–Halenda equation, whereas micropore

volume calculated by the t-method ( Brunauer, Emmett, & Teller, 1938). Surface functional groups determination was based on a titration method ( Boehm, 1994). Solutions of NaHCO3 (0.1 mol L−1), Na2CO3 (0.05 mol L−1), NaOH (0.1 mol L−1), and HCl (0.1 mol L−1) were prepared with distilled water. 50 mL

of these solutions www.selleckchem.com/products/ch5424802.html were added to vials containing 1 g of adsorbent, shaken for 24 h (100 rpm) and filtered. Five solution blanks were also prepared. The excess of base or acid was determined by back titration using NaOH (0.1 mol L−1) and HCl (0.1 mol L−1) VX-809 manufacturer solutions. Evaluation of the Point of Zero Charge (pHPZC) was based on a potentiometric titration procedure (Nunes et al., 2009). Three aqueous solutions of pHs 3, 6 and 11 were prepared. Several amounts of adsorbent (0.05, 0.1, 0.5, 1.0, 3.0, 7.0 and 10.0 g/100 g) were added to 20 mL of each solution. The aqueous suspensions were let to equilibrate for 24 h under agitation at 25 °C. The pH of each solution was measured using a pHmeter (Micronal, SP, Brazil) and the pHPZC was determined as the converging value from the pH vs. adsorbent mass curve. Batch experiments of adsorption were performed in 250 mL Erlenmeyer flasks agitated on a shaker at 100 rpm for pre-determined time intervals. In all experiments, a pre-determined amount of adsorbent was mixed with 150 mL PHE

solution. Preliminary tests, for evaluation of the effects of particle size, initial solution pH and adsorbent mass, were conducted at 25 °C and at a fixed initial PHE concentration (500 mg L−1). Effect of particle size (D) was evaluated in the ranges: D < 0.50 mm; 0.50 < D < 0.84 mm; D > 0.84 mm (pH 6, adsorbent dosage = 10 mg L−1). Effect of initial pH was evaluated in the range Vildagliptin of 2–10 (adsorbent dosage = 10 mg L−1) and of adsorbent dosage in the range of 5–50 g L−1 (pH = 6). Effect of contact time was evaluated at periods ranging from 5 min to 6 h and initial PHE concentrations from 300 to 1500 mg L−1, employing the best values obtained for initial pH, particle size and adsorbent concentration. After the specified periods, 2 mL aliquots were taken from the flasks and centrifuged. The PHE concentration was determined in the supernatant by a UV–Vis spectrophotometer (Hitachi U-2010) at 257 nm.

This entry was posted in Antibody. Bookmark the permalink.

Leave a Reply

Your email address will not be published. Required fields are marked *

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>